Polaris Sportsman 9921825 Page 49 Owner'S Manual Download | Manualshive

Page: 49 / 132

background image

46

OPERATION

Starting the Engine

1. Position the vehicle on a level surface outdoors or in a well-venti-

lated area.

2. Place the transmission in PARK.

3. Lock the parking brake.

Tip:

The starter interlock will prevent the engine from starting if the transmission
is in gear and the brake is not engaged.

4. Turn the fuel valve on.

5. Sit on the vehicle.

6. Do not use the choke if starting a warm engine. Excessive use of the

choke can cause the spark plug to become wet fouled.

7. If the engine is cold, pull the

choke knob out until it stops.

Tip:

The variable choke is fully on
when the knob is pulled com-
pletely out. The choke is off when
the knob is pushed completely in.
The choke can be adjusted gradu-
ally, depending on how much
choke is needed for starting. Be
sure the choke is off during opera-
tion, as excess fuel washing into
the engine oil will increase wear
on engine components.

8. If the knob doesn't stay where

positioned, increase the ten-
sion by rotating the tension
adjusting nut clockwise.

9. Move the engine stop switch to RUN.

10. Do not press the throttle while starting the engine.

Tension

Adjusting Nut

«
...
47
48
49
50
51
...
»

Summary of Contents for Sportsman 9921825





































































































































Reviews:

No comments

Related manuals for Sportsman 9921825

Brand: KAYO MOTOR Pages: 90

Brand: Go Kart Pages: 20

Brand: Logan Pages: 28

Brand: Can-Am Pages: 147

Brand: Erde Pages: 4

Dodge Grand Caravan

Brand: Savaria Pages: 44

Brand: Polaris Pages: 174

Raider mini 90S

Brand: Dazon Pages: 60

Brand: Polaris Pages: 179

Brand: Yamaha Pages: 141

Brand: Baja motorsports Pages: 55

Brand: Humbaur Pages: 56

All Terrain Vehicle 250

Brand: CROSSRUNNER Pages: 16

Evoquip Bison 120

Brand: Terex Pages: 224

Brand: Travel Lite Pages: 33

Brand: PLAYKIN Pages: 70

Brand: Honda Pages: 234

Brand: Arctic Cat Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands