Polaris Sportsman 9921825 Page 75 Owner'S Manual Download

Page: 75 / 132

MAINTENANCE

Oil and Filter Change

Oil Pump Priming

This priming procedure must be
performed whenever the oil hose
connection between the oil tank and
pump inlet has been disconnected.

1. Clamp or pinch off the vent line

approximately 2" (5 cm) from
the oil tank, between the end of
the oil tank vent fitting and the
vent line's pressure relief slit.

2. Start the engine. Allow it to idle

for 10-20 seconds.

3. Remove the vent line clamp. If the line is bled properly, you should

hear a rush of air, indicating that the line is properly primed and
ready for operation.

Tip:

If you do not hear air, the line has not bled. Repeat the priming procedure.

Clamp

Pressure

Relief Slit

Tank

(5 cm)

Summary of Contents for Sportsman 9921825





































































































































Search results

Summary of Contents for Sportsman 9921825

Reviews:

Related manuals for Sportsman 9921825

Brands by name

Popular brands

Polaris Sportsman 9921825, Owner'S Manual

Search results

Summary of Contents for Sportsman 9921825

Reviews:

Related manuals for Sportsman 9921825

Brands by name

Popular brands