Polaris Sportsman 9921825 Owner'S Manual Download Page 34 | Manualshive

Page: 34 / 132

Polaris Sportsman 9921825 Owner'S Manual Download Page 34

31

FEATURES AND CONTROLS

Choke

The choke assists in starting a cold engine. Refer to the engine starting
procedure on page 46 for correct choke and throttle settings during start-
ing.

Fuel Valve

The fuel valve is located under the
front storage box cover.

OFF: For vehicle storage and when
transporting.

ON: For normal operation.

Fuel Tank Cap

This vehicle is equipped with a
digital fuel gauge that will
indicate a low fuel condition.
Refuel when the gauge indi-
cates a low fuel condition.

Always refuel with the engine
stopped, and outdoors or in a
well ventilated area. Refuel on
a level surface.

Remove the fuel tank cap to
add fuel to the fuel tank. Use
either leaded or unleaded gaso-
line with a minimum pump
octane number of 87=(R+ M/2)
octane.

Do not use E-85 fuel

.

Fuel Filter

The in-line fuel filter should be replaced by your dealer after every 100
hours of operation, or annually. Do not attempt to clean the fuel filter.

OFF

ON

Fuel

Tank

Cap

«
...
32
33
34
35
36
...
»

Summary of Contents for Sportsman 9921825





































































































































Reviews:

No comments