Polaris Sportsman 9921825 Page 82 Owner'S Manual Download | Manualshive

Page: 82 / 132

background image

79

MAINTENANCE

Cooling System

Radiator Coolant

To ensure that the coolant maintains its ability to protect the engine,
Polaris recommends that you drain the system completely every two
years and add a fresh mixture of antifreeze and water.

Replace the coolant any time the cooling system has been drained for
maintenance or repair. If the recovery bottle has run dry, check the level
in the radiator. Add coolant as needed.

CAUTION!

Escaping steam can cause burns. Never remove the pressure cap

while the engine is warm or hot. Always allow the engine to cool before
removing the pressure cap.

1. Open the front box cover

and pull open the access
door.

2. Remove the pressure cap.

3. Using a funnel, slowly add

coolant through the radia-
tor filler neck.

4. Reinstall the pressure cap.

Use of a non-standard pres-
sure cap will not allow the
recovery system to func-
tion properly. Contact your
dealer for the correct replacement part.

5. Secure the access door.

6. Secure the box cover.

Radiator Cap

«
...
80
81
82
83
84
...
»

Summary of Contents for Sportsman 9921825





































































































































Reviews:

No comments

Related manuals for Sportsman 9921825

Brand: CF MOTO Pages: 365

MAVERICK Trail 2021 Series

Brand: Can-Am Pages: 195

RHINO FUEL INJECTION 700 FI 2008

Brand: Yamaha Pages: 192

Dune Buggy GT250

Brand: Hammerhead Pages: 25

Brand: Primo Water Pages: 12

FourTrax Foreman TRX500FE2 2018

Brand: Honda Pages: 279

Brand: Honda Pages: 229

Brand: Honda Pages: 159

Brand: Honda Pages: 71

Black-Topper Shooter II

Brand: Etnyre Pages: 51

Black-Topper SHOOTER Series

Brand: Etnyre Pages: 84

DEFENDER MAX Series 2021

Brand: Can-Am Pages: 211

Brand: Columbia Pages: 36

Brand: Humbaur Pages: 56

FEBER quad KRIPTON

Brand: Famosa Pages: 4

Brand: Kärcher Pages: 228

Brand: Cold Jet Pages: 31

1988 Citation LS

Brand: BOMBARDIER Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands