Polaris Sportsman 9921825 Page 65 Owner'S Manual Download | Manualshive

Page: 65 / 132

background image

62

MAINTENANCE

Periodic Maintenance Chart

Careful periodic maintenance will help keep your vehicle in the safest,
most reliable condition. Inspection, adjustment and lubrication of
important components are explained in the periodic maintenance chart.

Inspect, clean, lubricate, adjust and replace parts as necessary. When
inspection reveals the need for replacement parts, use genuine Polaris
parts available from your Polaris dealer.

Record maintenance and service in the Maintenance Log beginning on
page 128.

Service and adjustments are important for proper vehicle operation. If
you're not familiar with safe service and adjustment procedures, have a
qualified dealer perform these operations.

Maintenance intervals in the following chart are based upon average
riding conditions and an average vehicle speed of approximately 10
miles per hour. Vehicles subjected to severe use must be inspected and
serviced more frequently.

Severe Use Definition

• Frequent immersion in mud, water or sand
• Racing or race-style high RPM use
• Prolonged low speed, heavy load operation
• Extended idle
• Short trip cold weather operation

Pay special attention to the oil level. A rise in oil level during cold
weather can indicate contaminants collecting in the oil sump or crank-
case. Change oil immediately if the oil level begins to rise. Monitor the
oil level, and if it continues to rise, discontinue use and determine the
cause or see your dealer.

«
...
63
64
65
66
67
...
»

Summary of Contents for Sportsman 9921825





































































































































Reviews:

No comments

Related manuals for Sportsman 9921825

Brand: Panasonic Pages: 8

Brand: Yamaha Pages: 59

Brand: Taylor-Dunn Pages: 254

Trailblazer E2020

Brand: Evinrude Pages: 14

Brand: Can-Am Pages: 401

Street Rider 150MRX

Brand: Texas Pages: 33

Brand: Texas Pages: 49

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 141

Brand: Yamaha Pages: 262

Brand: JI-EE Pages: 61

Brand: Humbaur Pages: 56

Brand: U-Line Pages: 9

Brand: Landa Pages: 30

Brand: Jeep Pages: 16

Brand: Yamaha Pages: 172

Brand: Yamaha Pages: 150

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands