Polaris Scrambler 500 4x4 Owner'S Manual Download

Page: 55 / 129

OPERATION

Starting the Engine

Starting a Cold Engine

3. Move the engine stop switch to

RUN

NOTE:

Do not press the

throttle while starting the engine.

4. Turn the ignition key past the

position to engage the starter.

Activate the starter for a maximum of five seconds, releasing the

key when the engine starts. If the engine does not start, release the

key and wait five seconds. Then activate the starter for another

five seconds. Repeat this procedure until the engine starts.

5. If the engine slows or stops, position the choke knob half way in to

allow proper engine warm up.

6. Vary the engine RPM slightly with the throttle to aid in warm-up.

When the engine idles smoothly, push the choke all the way in.

Summary of Contents for Scrambler 500 4x4


































































































































Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands

Polaris Scrambler 500 4x4, Owner'S Manual

Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands