Polaris Scrambler 500 4x4 Page 74 Owner'S Manual Download

Page: 74 / 129

MAINTENANCE AND LUBRICATION

Periodic Maintenance Schedule

Item

Hours/

Miles

Frequency Remarks

Taillight/brakelight

Pre-Ride Pre-Ride

Check operation daily; ap-

ply Polaris dielectric grease

to socket when replaced

Air filter,

main element

Weekly

Inspect; replace as needed

Transmission oil

20 hrs.

Monthly

Inspect level monthly;

change annually

Battery

20 hrs.

Monthly

Check terminals; clean

Engine breather

filter

20 hrs.

Monthly

Inspect; replace annually

and as needed

Brake pad wear

10 hrs.

Monthly

Inspect periodically

Front and rear

gearcase oil

100 hrs. Monthly

Check monthly; change

annually

Engine cylinder

head and cylinder

base fasteners

25 hrs.

3 months

Inspect (re-torque required

at first service only)

General lubrication

50 hrs.

3 months

Lubricate all fittings, pivots,

cables, etc.

Engine oil level/oil

change

100 hrs./

1000 mi.

6 months

Check level daily; break-in

service at one month;

change oil more often in

cold weather

Oil filter

100 hrs./

1000 mi.

6 months

Replace with oil change

Engine breather

hose

100 hrs. 6 months

Inspect

More often under severe use, such as dirty or wet conditions

Emission Control System Service (California)

Dealer service item

Summary of Contents for Scrambler 500 4x4


































































































































Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands

Polaris Scrambler 500 4x4, Owner'S Manual

Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands