Polaris Scrambler 500 4x4 Page 75 Owner'S Manual Download

Page: 75 / 129

MAINTENANCE AND LUBRICATION

Periodic Maintenance Schedule

Item

Hours/

Miles

Frequency Remarks

Carburetor float

bowl

50 hrs.

6 months

Drain bowl periodically and

prior to storage

Throttle Cable/ETC

Switch

50 hrs.

6 months

Inspect; adjust; lubricate;

replace if necessary

Choke (enricher)

cable

50 hrs.

6 months

Inspect; adjust; lubricate;

replace if necessary

Coolant strength/

pressure test sys-

tem

100 hrs. 6 months

Inspect strength seasonal-

ly; pressure test system

annually

Front hubs/fluid

check (AWD)

50 hrs.

6 months

Check monthly

Shift linkage

50 hrs.

6 months

Inspect; adjust

Drive belt

50 hrs.

6 months

Inspect; replace as needed

Steering

50 hrs.

6 months

Inspect daily; lubricate

Front suspension

50 hrs.

6 months

Inspect; lubricate; tighten

fasteners

Rear suspension

50 hrs.

6 months

Inspect; tighten fasteners

Drive chain(s)

50 hrs.

6 months

Inspect daily; adjust and lu-

bricate if needed

Rear axle

50 hrs

6 months

Inspect bearings

Spark plug

100 hrs. 12 months

Inspect; replace as needed

Ignition Timing

100 hrs. 12 months

Inspect; adjust as needed

Improperly performing the procedures marked with a

could

result in component failure and lead to serious injury or death.

Have an authorized Polaris dealer perform these services.

WARNING

Summary of Contents for Scrambler 500 4x4


































































































































Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands

Polaris Scrambler 500 4x4, Owner'S Manual

Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands