Polaris Scrambler 500 4x4 Owner'S Manual Download Page 87

Page: 87 / 129

MAINTENANCE AND LUBRICATION

Lubrication Recommendations

Drive Chain

Polaris ATV drive chains are equipped with o-ring-sealed, permanently

greased pins and rollers. However, the outer surfaces of the roller must

be lubricated.
Always inspect the drive chain prior to operating the vehicle. Check for

damaged or missing o-rings or damaged rollers. Also check for correct

slack adjustment. Maintain the stone guard to rear sprocket clearance

at 1/8

″

(.3 cm).

Regularly lubricate the drive chain with Polaris Chain Lube, an SAE

80-90 lube or an approved o-ring chain spray lube. See page 117 for the

part numbers of Polaris products.

Washing the drive chain with a high pressure washer or gasoline

can cause damage to the o-rings, causing premature wear and

drive chain failure. Do not use a high pressure washer or

gasoline to clean the drive chain.

CAUTION

Summary of Contents for Scrambler 500 4x4


































































































































Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Polaris Scrambler 500 4x4, Owner'S Manual, Page: 87 / 129

Search results

Summary of Contents for Scrambler 500 4x4

Reviews: