Polaris Scrambler 500 4x4 Owner'S Manual Download

Page: 54 / 129

OPERATION

Starting the Engine

Starting a Cold Engine

1. Place the transmission in neutral

and lock the parking brake.

Make sure the fuel tank valve is

on.

2. Sit on the vehicle and pull the

choke knob out until it stops (1).

NOTE:

If the knob doesn’t stay

where positioned, increase the

tension by rotating the tension

adjusting nut (2) clockwise.

NOTE:

The variable choke is fully on

when the knob is pulled completely out.

The choke is off when the knob is pushed

completely in. The choke can be

adjusted gradually, depending on how

much choke is needed for starting. Be

sure the choke is off during operation, as

excess fuel washing into the engine oil

will increase wear on engine

components.

Engine exhaust contains poisonous carbon monoxide and can

cause loss of consciousness resulting in severe injury or death.

Never run an engine in an enclosed area.

WARNING

Operating the vehicle immediately after starting could cause

engine damage. Allow the engine to warm up for several

minutes before operating the vehicle.

CAUTION

Summary of Contents for Scrambler 500 4x4


































































































































Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands

Polaris Scrambler 500 4x4, Owner'S Manual

Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands