Polaris Scrambler 500 4x4 Owner'S Manual Download

Page: 105 / 129

102

MAINTENANCE AND LUBRICATION

Vehicle Immersion

If it’s impossible to take your ATV to a dealer before starting it, follow

the steps outlined below.
1. Move the ATV to dry land or at the

very least, to water below the

footrests.

2. Check the airbox for any water. Drain

and dry it if water is present.

3. Turn the fuel valve off.
4. Remove the spark plug.
5. Turn the engine over several times

using the electric start.

6. Loosen the carburetor drain screw (1).
7. Dry the spark plug and reinstall, or replace it with a new plug.
8. Tighten the carburetor drain screw.
9. Turn the fuel valve on.
10. Attempt to start the engine. If necessary, repeat the drying

procedure.

11. Take the ATV to your dealer for service as soon as possible,

whether you succeed in starting it or not.

NOTE:

If water has been ingested into the PVT, follow the procedure

on page 105 for drying out the PVT.

If your vehicle becomes immersed, major engine damage can

result if the machine is not thoroughly inspected. Take the

vehicle to your dealer before starting the engine.

CAUTION

Summary of Contents for Scrambler 500 4x4


































































































































Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands

Polaris Scrambler 500 4x4, Owner'S Manual

Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands