Polaris Scrambler 500 4x4 Owner'S Manual Download

Page: 47 / 129

FEATURES AND CONTROLS

Choke

The choke assists in starting a cold engine. Refer to the engine starting

procedure on page 51 for correct choke and throttle settings during

starting.

Fuel Valve

The fuel valve (1) is located on the left side of

the vehicle, below the fender. It has three

positions:
OFF: For vehicle storage and when transporting.
ON: For normal operation.
RES: For reserve supply if main

supply is exhausted.

NOTE:

There’s about a 7 to 10 mile

(11.2 to 16 km) range on reserve gas.

Always refill the gas tank as soon as

possible after using the reserve supply.
Always return the valve to the

position after refueling.

Fuel Tank

The fuel tank filler cap (2) is located

directly below the handlebar. Use

either leaded or unleaded gasoline with

a minimum pump octane number of

87=(R+ M/2) octane. Refer to the

specifications section at the rear of this

manual for tank capacity.

Fuel Filter

The in-line fuel filter should be replaced by your dealer after every 100

hours of operation, or annually. Do not attempt to clean the fuel filter.

Summary of Contents for Scrambler 500 4x4


































































































































Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands

Polaris Scrambler 500 4x4, Owner'S Manual

Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands