Polaris Scrambler 500 4x4 Owner'S Manual Download

Page: 36 / 129

SAFETY

Safety Decals and Locations

Warning decals have been placed on the ATV for your protection. Read

and follow the instructions of the decals on the ATV carefully. If any

of the decals depicted in this manual differ from the decals on your

ATV, always read and follow the instructions of the decals

on the ATV

If any decal becomes illegible or comes off, contact your Polaris dealer

to purchase a replacement. Replacement

safety

decals are provided by

Polaris at no charge. The part number is printed on the decal.

7079604

WARNING

Pushing reverse

override button

may cause

sudden increases

in power and

traction if too

much throttle is

applied. Loss of

control or forward

flipover may

result, especially

in AWD. See

Owner’s Manual.

Never operate this vehicle on HILLS steeper than 25 degrees

To prevent flipover on hilly terrain, when going up or down, use throttle

and brakes gradually.

REVERSE operation can be dangerous, even at low speeds. Steering be-

comes difficult. To prevent flipover, avoid sudden braking or sharp turns.

Use OVERRIDE for reverse speed limiter with caution. To prevent loss

of control, never activate override button with open throttle.

PARKING BRAKE may relax when used for more than 5 minutes. When

parking on grades, leave shift in forward.

WARNING

7079085

Moving parts hazard under belt-clutch guard. To

prevent serious injury, do not operate vehicle

with guard removed.

Do not modify engine or clutch. Doing so can

cause part failure, possible imbalance, and

excessive engine RPM, which can result in serious

injury or death.

NO STEP

7078689

WARNING

Summary of Contents for Scrambler 500 4x4


































































































































Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands

Polaris Scrambler 500 4x4, Owner'S Manual

Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands