Polaris Scrambler 500 4x4 Owner'S Manual Download

Page: 85 / 129

MAINTENANCE AND LUBRICATION

Lubrication Recommendations

Transmission Oil Check

The transmission lubricant level should be checked every six months or

1000 miles (1600 km), whichever comes first. Maintain the oil level at

the bottom of the fill hole threads. Change transmission oil annually.

We recommend the use of AGL Synthetic Gearcase Lubricant. See

page 117 for the part numbers of Polaris products.
1. Position the ATV on a level

surface and remove the fill plug (1),

which is located on the right side

of the machine, behind the

propshaft shield.

2. Add the recommended lubricant as

needed to maintain the oil level at

the bottom of the fill hole threads.

3. Reinstall the fill plug.

Transmission Oil Change

1. Remove the propshaft shield from the right side of the vehicle to

access the fill plug. Remove the fill plug.

2. Remove the transmission drain plug located on the bottom

left-hand side and drain the oil into an appropriate container.

Discard used oil properly.

3. Clean and reinstall the drain plug. Torque to 14 ft. lbs. (19 Nm).
4. Add the proper amount of the recommended lubricant. Refer to the

specifications section beginning on page 114 for capacities.

5. Reinstall the fill plug and check for leaks.
6. Reinstall the propshaft shield.

Summary of Contents for Scrambler 500 4x4


































































































































Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands

Polaris Scrambler 500 4x4, Owner'S Manual

Search results

Summary of Contents for Scrambler 500 4x4

Reviews:

Related manuals for Scrambler 500 4x4

Brands by name

Popular brands