Playnation Cartecay 1701 Assembly Download Page 48

Page: 48 / 79

BOTTOM ROCK WALL BOARD

5/4" X 6 X 47-1/2"

ROCK WALL BOARD

#8 X 2" WOOD SCREW

MAKE SURE ROCK WALL CENTER

SUPPORT IS NOT BLOCKING THIS HOLE

ARCH ROCK WALL SIDE SUPPORT

ARCH ROCK WALL CENTER

SUPPORT

STEP 13: ATTACHING THE ROCK WALL CENTER SUPPORT

1: BEGIN WITH THE 5/4 X 6 X 47-1/2" ROCK WALL BOARD AND SECURE IT TO THE ARCH ROCK WALL SIDE SUPPORT

WITH TWO #8 X 2" WOOD SCREWS PER SIDE. THE ROUNDED EDGE OF THE ROCK WALL BOARD SHOULD BE

AGAINST THE CORNER POSTS BEFORE ATTACHING.

2: NEXT THE 5/4 X 6 X 47-1/2" BOTTOM ROCK WALL BOARD WITH ONE HOLE WILL MOUNT AT THE BOTTOM WITH

THE 7/8" HOLE TOWARDS THE BOTTOM. THIS BOARD WILL BE AT 44" FROM THE TOP ROCK WALL BOARD AND

FLUSH TO THE ROCK WALL SIDE SUPPORTS. SECURE WITH #8 X 2" WOOD SCREWS.

3: PLACE THE ARCH ROCK WALL CENTER SUPPORT BEHIND THE ROCK WALL BOARDS AND CENTER IT UNDER THE

SMALL HOLES. FASTEN THE ARCH ROCK WALL CENTER SUPPORT TO THE ROCK WALL BOARDS WITH #8 X 2"

WOOD SCREWS.

44"

BOTTOM

TOP

ARCH ROCK WALL

CENTER SUPPORT

Summary of Contents for Cartecay 1701















































































Search results

Summary of Contents for Cartecay 1701

Reviews:

Related manuals for Cartecay 1701

Brands by name

Popular brands

Playnation Cartecay 1701, Assembly

Search results

Summary of Contents for Cartecay 1701

Reviews:

Related manuals for Cartecay 1701

Brands by name

Popular brands