Playnation Cartecay 1701 Assembly Download Page 47

Page: 47 / 79

STEP 12: ATTACHING THE ARCH ROCK WALL SIDE SUPPORTS

1: MOUNT THE ARCH ROCK WALL SIDE SUPPORT ON TOP OF THE ROCK WALL SUPPORT, MAKE SURE THAT THE

TOP END OF THE ARCH ROCK WALL SIDE SUPPORT IS FLUSH WITH THE CORNER POST.

2: FIRST, FASTEN A #8 X 3" WOOD SCREW THROUGH THE ARCH ROCK WALL SIDE SUPPORT TOP HOLE INTO THE

ROCK WALL SUPPORT. MAKE SURE THAT THIS BOARD IS ALIGNED WITH THE ROCK WALL SUPPORT.

3: SECOND, FASTEN THE SECOND #8 X 3" WOOD SCREW THROUGH THE ARCH ROCK WALL SIDE SUPPORT

BOTTOM HOLE INTO THE ROCK WALL SUPPORT. MAKE SURE THAT THIS BOARD IS ALIGNED WITH THE ROCK WALL

SUPPORT.

4: THIRD, FASTEN #8 X 3" WOOD SCREW THROUGH THE ROCK WALL SUPPORT INTO THE ARCH ROCK WALL

SUPPORT. MAKE SURE BOTH BOARDS ARE FLUSH ON THE SIDES AND WHERE THEY MEET.

WOOD SCREW

(2ND)

#8 X 3"

WOOD SCREW

#8 X 3"

(3RD)

(1ST)

#8 X 3" WOOD SCREW

2 X 6 X 54"

ARCH ROCK WALL

SIDE SUPPORT

ROCK

WALL

SUPPORTS

Summary of Contents for Cartecay 1701















































































Search results

Summary of Contents for Cartecay 1701

Reviews:

Related manuals for Cartecay 1701

Brands by name

Popular brands

Playnation Cartecay 1701, Assembly

Search results

Summary of Contents for Cartecay 1701

Reviews:

Related manuals for Cartecay 1701

Brands by name

Popular brands