Playnation Cartecay 1701 Assembly Download Page 78

Page: 78 / 79

STEP 43: GROUND STAKES

GROUND STAKES

1: PLACE THE GROUND STAKES ON THE OUTSIDE OF THE SWING LEGS AS SHOWN BELOW.

2: HAMMER EACH GROUND STAKE IN AT AN ANGLE SIMILAR TO WHAT IS SHOWN. USE CAUTION WHEN

HAMMERING SO THAT YOU DO NOT MAR THE WOOD. LEAVE THE TOP PORTION OF THE GROUND STAKE

ABOVE THE GROUND FAR ENOUGH SO THAT YOU CAN STILL GET THE SCREW INTO THE HOLE AT THE TOP OF

THE STAKE.

3: SECURE EACH STAKE TO THE SWING LEGS WITH THE SCREWS PROVIDED WITH THE STAKES.

4: HAMMER A GROUND STAKE ON THE INSIDE OF EACH CORNER POST NEAR THE ROCK WALL. USE

CAUTION WHEN HAMMERING SO THAT YOU DO NOT MAR THE WOOD. LEAVE THE TOP PORTION OF THE

GROUND STAKE ABOVE THE GROUND FAR ENOUGH SO THAT YOU CAN STILL GET THE SCREW INTO THE

HOLE AT THE TOP OF THE STAKE.

5: SECURE EACH STAKE TO THE CORNER POSTS WITH THE SCREWS PROVIDED WITH THE STAKES.

CORNER

POSTS

SWING LEGS

GROUND STAKE

SCALE 1 : 8

DETAIL A

GROUND STAKE

SCREW THAT

COMES WITH

SWING LEG

STAKE

SCALE 1 : 8

DETAIL B

GROUND STAKE

WOOD SCREW

THAT COMES

WITH GROUND

CORNER POST

Summary of Contents for Cartecay 1701















































































Search results

Summary of Contents for Cartecay 1701

Reviews:

Related manuals for Cartecay 1701

Brands by name

Popular brands

Playnation Cartecay 1701, Assembly

Search results

Summary of Contents for Cartecay 1701

Reviews:

Related manuals for Cartecay 1701

Brands by name

Popular brands