Playnation Cartecay 1701 Assembly Download Page 42

Page: 42 / 79

STEP 7: ATTACHING ARCH FACE BOARD AND DECK SUPPORT

1: THE 2 X 6 X 47-1/2" ARCH FACE BOARD (WITH FOUR PRE-DRILLED HOLES) ATTACHES TO THE SET OF HOLES

BELOW THE TARP SUPPORT BOARD. ATTACH THE TOP HOLES OF THE ARCH FACE BOARD USING 5/16 X 4-1/2" HEX

BOLTS AND 5/16" WASHERS. ATTACH THE BOTTOM HOLES OF THE ARCH FACE BOARD USING 5/16 X 3-1/2" LAG

SCREWS AND 5/16" WASHERS.

2: THE 2 X 4 X 47-1/2" DECK SUPPORT BOARDS (WITH TWO PRE-DRILLED HOLES) ATTACH TO THE SET OF HOLES

ABOVE THE SANDBOX BOARD AND THE GROUND SUPPORT BOARD ON THE INSIDE OF THE LEFT AND RIGHT SIDE

CORNER POSTS WITH 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS. THE HOLES SHOULD BE OFFSET DOWN ON

BOTH DECK SUPPORT BOARDS.

DECK SUPPORT

(OFFSET DOWN)

HEX BOLT

FRONT OF PLAYSET

5/16 X 4-1/2"

5/16" WASHER

4-1/2"

5/16" X 3-1/2"

HEX BOLT

LAG SCREW

5/16" WASHER

2 X 4 X 47-1/2"

5/16" WASHER

5/16

2 X 6 X 47-1/2"

ARCH FACE BOARD

Summary of Contents for Cartecay 1701















































































Search results

Summary of Contents for Cartecay 1701

Reviews:

Related manuals for Cartecay 1701

Brands by name

Popular brands

Playnation Cartecay 1701, Assembly

Search results

Summary of Contents for Cartecay 1701

Reviews:

Related manuals for Cartecay 1701

Brands by name

Popular brands