Peter electronic VersiStart p III 105 Assembly And Commissioning Instructions Download Page 71

Page: 71 / 108

VersiStart p III

Description:

Sets the amount of brake torque the VersiStart p III will use to slow
the motor.

3P – DC Brake Time-2

Range:

0:01 - 0:30 (minutes:seconds)

Default:

1 second

Description:

Sets the duration for DC injection during a braking stop.

3Q – Brake Current Limit-2

Range:

100% - 600% FLC

Default:

250%

Description:

Sets the current limit for soft brake.

3R – Soft Brake Delay-2

Range:

400 - 2000 milliseconds

Default:

400 milliseconds

Description:

Sets the time the soft starter will wait after a stop signal is received,
before it begins to supply braking current to the motor. Set to allow
time for K1 and K2 to switch.

10.8 4 Auto-Start/Stop

The VersiStart p III can be configured to automatically start and/or stop the motor
once per day. For auto-start/stop to operate:

•

parameter 4A

Auto-Start/Stop Mode

must be set to 'Enable'

•

parameter 1A

Command Source

must be set to 'Clock'

•

the reset input must be closed

•

the start input (11, 12) must be active. This allows the VersiStart p III to be

stopped via the digital inputs in an emergency.

•

parameters 4B ~ 4V: Set as required.

4A – Auto-Start/Stop Mode

Options:

Disable (default)
Enable

Description:

Enable or disable auto-start/stop operation.

4B – Sunday Mode

Options:

Start/Stop Disable
(default)

Disables auto-start/stop control. Any times
scheduled in parameters 4C or 4D will be
ignored.

Start Only Enable

Enables auto-start control. Any auto-stop times
scheduled in parameter 4D will be ignored.

Stop Only Enable

Enables auto-stop control. Any auto-start times
scheduled in parameter 4C will be ignored.

Start/Stop Enable

Enables auto-start and auto-stop control.

Description:

Enables or disables auto-start/stop for Sunday.

4C – Sunday Start Time

Range:

00:00 - 23:59

Default:

00:00

Summary of Contents for VersiStart p III 105













































































































Search results

Summary of Contents for VersiStart p III 105

Reviews:

Related manuals for VersiStart p III 105

Brands by name

Popular brands

Peter electronic VersiStart p III 105, Assembly And Commissioning Instructions

Search results

Summary of Contents for VersiStart p III 105

Reviews:

Related manuals for VersiStart p III 105

Brands by name

Popular brands