Pentair FLECK 5800, Service Manual

Page: 46 / 48

5810 PERFORMANCE DATA
Model Name:
may include SXT, XTRI or XTRI
5810 - 1.00 ft
3
5810 - 1.25 ft
3
test unit
5810 - 1.50 ft
3
5810 - 2.0 ft
3
5810 - 3.00 ft
3
Maximum Rated Service Flow
(gpm) (W/upper collector)
13.1 14.9 13.7 17.2 18.9
Pressure Drop at Rated
Service Flow Rate (gpm)"
15 15 15 15 15
Rated Capacity
(grains @ lbs. of salt)" 17,834 @ 4.0
27,949 @ 9.0
32,225 @ 15.0
22,918 @ 5.0
35,915 @ 11.25
41,410 @ 18.75
27,501 @ 6.0
43,098 @ 13.5
49,692 @ 22.5
36,668 @ 8.0
57,464 @ 18.0
66,256 @ 30.0
55,003 @ 12.0
86,196 @ 27.0
99,384 @ 45.0
Rated Efficiency
(grains/lb. Salt @ lbs. of salt)"
4,460 @ 4.0 4,580 @ 5.0 4,580 @ 6.0 4,580 @ 8.0 4,580 @ 12.0
Maximum Flow Rate During
Regeneration (gpm)
2.0 2.4 2.4 3.5 5
Resin Volume - ft
3
Resin Type - 8% strong acid cation"
1 1.25 1.5 2 3
Tank size
9" x 48" 10" x 47" 10" x 54" 12" x 52" 14" x 65"
Backwash 8 8 8 8 8
Brine Draw & Slow Rinse
@ lb of Salt
58 @ 4.0
76 @ 9.0
95 @ 15.0
46 @ 5.0
58 @ 11.25
72 @ 18.75
54 @ 6.0
68 @ 13.5
86 @ 22.5
49 @ 8.0
62 @ 18.0
78 @ 30.0
58 @ 12.0
76 @ 27.0
98 @ 45.0
Rapid Rinse 6 6 6 6 6
Fill @ lb of Salt
11 @ 4.0
24 @ 9.0
40 @ 15.0
14 @ 5.0
30 @ 11.25
50 @ 18.75
16 @ 6.0
36 @ 13.5
60 @ 22.5
11 @ 8.0
24 @ 18.0
40 @ 30.0
8 @ 12.0
18 @ 27.0
30 @ 45.0
Operating Pressure:20 -125 psi or 1.4 – 8.8 kg/Centimeter2, Operating Temperature: 34 - 110° F or 1.1 – 43.3° C Acceptable Salt Type: Sodium Chloride
All Systems above tested at 35psi +/- 5 psi, pH of 7.5 +/- 0.5, Capacity Testing Flow Rate = 50% of the rated service flow rate for the various size systems
These water softener systems have been tested by WQA and conform to NSF/ANSI 44 for specific performance claims as
verified and substantiated by test data. The rated salt efficiencies above were also determined in accordance with NSF/ANSI
44 and are only valid at the salt dosage referenced above. An efficiency rated water softener is a demand initiated regeneration
(DIR) softener which also complies with specific performance specifications intended to minimize the amount of regenerant
brine and water used in its operation. Efficiency rated water softeners shall have a rated salt efficiency of not less that 3350
grains of total hardness exchanged per pound of salt (based on NaCl equivalency) (477 grams of total hardness exchanged per
kilogram of salt), and shall not deliver more salt than its listed rating. The rated efficiency of the water softener, the salt dosage
at that efficiency, the capacity at that salt dosage and that of the efficiency is only valid at the stated salt dosage. Efficiency is
measured by a laboratory test described in NSF/ANSI 44. The test represents the maximum possible efficiency the system can
achieve. Operational efficiency is the actual efficiency achieved after the system has been installed. It is typically less than the
efficiency due to individual application factors including water hardness, water usage, and other contaminants that reduce the
water softener’s capacity. These systems are not intended to be used for treating water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system. Refer to the system Installation and Service Manuals
for set-up and programming instructions.
Contact your local dealer for parts and service. See your owner’s manual for warranty information.
Tested and Certified by the WQA to NSF/
ANSI Standard 44 & 372 for softener
performance & lead free compliance
and CSA B483.1
Pentair Residential Filtration, LLC
13845 Bishops Drive Suite 200
Brookfield, Wisconsin 53005
PHONE: (262)-238-4400
C US
Valv
e Cy
cle T
ime
Se
tting
s (minut
es)
Rev. B 7/09/19
46 • FLECK 5800/5810/5812 XTRI Service Manual