Chapter 4
Settings — [PICTURE] menu
90 - ENGLISH
Setting item
Details
[LIGHTS OUT FADE-IN]
(Setting of fade-in when
lighting up again)
[OFF]
Does not set the fade-in of the image when the light source is
turned on again from the condition that the light source was turned
off with [LIGHTS OUT TIMER].
[0.5s] - [10.0s]
Sets the time to fade in the image when the light source is turned
on again from the condition that the light source was turned off with
[LIGHTS OUT TIMER].
Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] -
[4.0s] can be selected in increments of 0.5.
[LIGHTS OUT FADE-OUT]
(Setting of fade-out when
lighting off)
[OFF]
Does not set the fade-out of the image when the light source is
turned off with [LIGHTS OUT TIMER].
[0.5s] - [10.0s]
Sets the time to fade out the image when the light source is turned
off with [LIGHTS OUT TIMER].
Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] -
[4.0s] can be selected in increments of 0.5.
[MANUAL INTENSITY]
(Manual light source
adjustment)
[0] - [255]
The larger the value, the stronger the correction.
Can be set in increments of 1. (Factory setting: 255)
[DYNAMIC GAMMA]
(Adjustment of signal
compensation)
[OFF]
Does not compensate the signal.
[1]
Slightly compensates the signal.
[2]
Moderately compensates the signal.
[3]
Strongly compensates the signal.
[MULTI PROJECTOR SYNC]
Sets the contrast synchronization function.
This setting item is common with the following menu item.
f
The [PROJECTOR SETUP] menu
→
[MULTI PROJECTOR
SYNC]
Refer to the [PROJECTOR SETUP] menu
→
[MULTI PROJECTOR
SYNC] (
x
page 141) for details.
Note
f
[LIGHTS OUT SIGNAL LEVEL] cannot be set when [LIGHTS OUT TIMER] is set to [DISABLE].
f
When [LIGHTS OUT TIMER] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on again
from the state that the light source has turned off by this function.
g
When the brightness level of the image signal being input has exceeded the value set in [LIGHTS OUT SIGNAL LEVEL]
g
When the input signal is gone
g
When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed
f
The signal compensation of the dynamic contrast NX function varies depending on the values set in [AUTO CONTRAST], [BRIGHT SIGNAL
LEVEL] and [DYNAMIC GAMMA].
f
The dynamic contrast NX function does not operate while measuring the brightness and the color.
f
The contrast synchronization function is a function to display a combined screen with a balanced contrast by sharing the brightness level of
the image signal input to each projector when a multi-display is constructed by combining the projected image of multiple projectors.
[DYNAMIC CONTRAST]
Light adjustment of the light source and signal compensation are performed automatically according to the image
to make the contrast optimum for the image.
Performs conventional correction to adjust the black level by decreasing the general brightness.
1) Press
as
to select [DYNAMIC CONTRAST].
2) Press
qw
or the <ENTER> button.
f
The
[DYNAMIC CONTRAST]
individual adjustment screen is displayed.
3) Press
qw
to switch the item.
f
The items will switch each time you press the button.
[OFF]
Disables the dynamic contrast function.
[1]
Adjusts the light source and compensates signals to a small extent.
[2]
Adjusts the light source and compensates signals to a moderate extent.
[3]
Adjusts the light source and compensates signals to a large extent.
[USER]
Set any desired correction.
Refer to “Performing desired correction” (
x
page 91) for details.
