MAINTENANCE
SCHEDULE FOR SERVICE
MAINTENANCE
DAILY
WEEKLY
MONTHLY
EVERY SIX
MONTHS
100 HOURS 200 HOURS
Clean squeegee assembly. Check blades for wear or damage. Check if
adjustment needed to squeegee height
X
Clean out recovery tank inside and out and float shut off assembly.
Check both for damage. Leave recovery tank open during storage
X
Empty and clean out debris tray in the recovery tank
X
Empty any debris from front fill port strainer
X
Clean pads / brushes and check for wear or chemical build up
X
Check handles, knobs and switches for damage
X
Charge batteries (if machine used longer than 30 minutes)
X
Check hoses for wear, blockages or damage
X
Check on-board chemical container level (if scrubber is equipped with
on-board chemical injection system)
X
Clean outside of solution tank and clean inline solution filter. Check both
for damage
X
Check wet battery water level and add distilled water if necessary
X
Check splash guard around scrub head for damage (disk models only)
X
Thoroughly clean entire machine
X
Check Bromine puck in TTS. Replace if it’s 25% of it’s original size
X
Visually inspect HEPA filter
X
Check linkages and connectors for wear / damage
X
Check all bearings and wheels for noise or loose hardware
X
Check recovery tank lid gasket for wear or damage
X
Check batteries for cracks, corrosion or signs of overheating
X
Check all screws and nuts. Tighten if necessary
X
Inspect isolators (orbital units only)
X
Check for loose wires or connections
X
Clean batteries and terminals
X
Blow out dust in motors
X
Clean pivot points on squeegee and scrub deck linkages
X
NOTE:
With regular maintenance, the lifetime of your machine and its safe operation are extended and ensured. Scheduled maintenenace should be
performed by qualified personnel or by an authorized service center.
WARNING:
These maintenance procedures must be performed with the machine off and the batteries disconnected. Make sure to read all safety
instructions prior to performing maintenance.
Summary of Contents for S Series
