Orion OLW-4651, User Manual

Page: 31 / 42

- 58 - - 59 -
ORION
Hybrid Video System
- Send To MLCD
• Send the same command for all MLCD. No response will be made.
- Receive Data
STX CMD LENGTH
Data
Check sum ETX
ID(1Byte)
Master
Image Processor
Module ID
IP ID
Value 0X02 0x89 0X02 Variable 0x01 Variable 0x03
• ID Range (0x11~0x94): Upper Byte is Image Processor Module Set ID(1~9) and Lower Byte is the ID of IP Board(1~4.) In case of 4 LCD
sets, IDs will be 0x11, 0x12, 0x13, and 0x14.
• Check Sum : Add values from STX to Data and execute logical operation “NOT.”
10. Factory Data
- Apply the Picture Control values adjusted in the factory.
A. General Command
STX CMD LENGTH
Data
Check sum ETX
ID(1Byte)
Master
Image Processor
Module ID
IP ID
Value 0X02 Variable 0X02 Variable Variable 0x01 Variable 0x03
- Send To MLCD
- CMD : 0x82(Save), 0x83(Load)
• The command can be executed only for Power On status.
• The present Color Temperature value is indicated based on the current mode (Normal Mode/ Studio Mode.)
• Use “Get Picture Control Data” after sending the command to check whether the Data was applied properly.
• ID Range (0x11~0x94): Upper Byte is Image Processor Module Set ID(1~9) and Lower Byte is the ID of IP Board(1~4.) In case of 4 LCD
sets, IDs will be 0x11, 0x12, 0x13, and 0x14.
• Check Sum : Add values from STX to Data and execute logical operation “NOT.”
• Commands cannot be executed with Broadcast mode.
- Receive Data
STX CMD LENGTH
Data
Check sum ETX
ID(1Byte)
Master
Image Processor
Module ID
IP ID
Value 0X02 Variable 0X02 Variable Variable 0x01 Variable
0x03
• ID Range (0x11~0x94): Upper Byte is Image Processor Module Set ID(1~9) and Lower Byte is the ID of IP Board(1~4.) In case of 4 LCD
sets, IDs will be 0x11, 0x12, 0x13, and 0x14.
• Check Sum : Add values from STX to Data and execute logical operation “NOT.”
• ID Range (0x11~0x94): Upper Byte is Image Processor Module Set ID(1~9) and Lower Byte is the ID of IP Board(1~4.) In case of 4 LCD
sets, IDs will be 0x11, 0x12, 0x13, and 0x14.
• Check Sum : Add values from STX to Data and execute logical operation “NOT.”
8. Firmware Default(Flash Screen Data Load)
- Initialize the firmware as the phase before adjusting any values at the factory
STX CMD LENGTH
Data
Check sum ETX
ID(1Byte)
Master
Image Processor
Module ID
IP ID
Value 0X02 0x81 0X02 Variable Variable 0x01 Variable 0x03
- Send To MLCD
- CMD : 0x81
• ID Range (0x11~0x94): Upper Byte is Image Processor Module Set ID(1~9) and Lower Byte is the ID of IP Board(1~4.) In case of 4 LCD
sets, IDs will be 0x11, 0x12, 0x13, and 0x14.
• Check Sum : Add values from STX to Data and execute logical operation “NOT.”
• Commands cannot be executed with Broadcast mode.
- Receive Data
STX CMD LENGTH
Data
Check sum ETX ID(1Byte)
Master
Image Processor
Module ID
IP ID
Value 0X02 0x81 0X02 Variable Variable 0x01 Variable 0x03
• ID Range (0x11~0x94): Upper Byte is Image Processor Module Set ID(1~9) and Lower Byte is the ID of IP Board(1~4.) In case of 4 LCD
sets, IDs will be 0x11, 0x12, 0x13, and 0x14.
• Check Sum : Add values from STX to Data and execute logical operation “NOT.”
9. Gamma Control
A. General Command
STX CMD LENGTH
Data
Check sum ETX ID(1Byte)
Master Control
Image Processor
Module ID
IP ID
Value 0X02 0x89 0x03 Variable Variable 0x01 Variable Variable 0x03
- Send To MLCD
- CMD : 0x89
- Control Value : 1(0x01)~6(0x06)
• ID Range (0x11~0x94): Upper Byte is Image Processor Module Set ID(1~9) and Lower Byte is the ID of IP Board(1~4.) In case of 4 LCD
sets, IDs will be 0x11, 0x12, 0x13, and 0x14.
• Check Sum : Add values from STX to Data and execute logical operation “NOT.”
B. Broadcast Command
STX CMD LENGTH
Data
Check sum ETX ID(1Byte)
Control
Image Processor
Module ID
IP ID
Value 0X02 0x89 0X02 0x00 Variable Variable 0x03