Olivetti d-Color MF220 Copy Operations Download Page 152 | Manualshive

Page: 152 / 315

background image

[System Settings]

7

7-4

d-Color MF360/280/220 (Version 3)

7.1

7.1

[System Settings]

Configure the basic functions of this machine.

7.1.1

[Power Save Settings]

Configure the settings for the power-saving mode.

%

Press the

Utility/Counter

key

ö

[Administrator Settings]

ö

[System Settings]

ö

[Power Save Set-

tings].

Settings

[Low Power Mode Set-
tings]

Enter a time period before switching to the lower power mode when this
machine is not being operated.

[Sleep Mode Settings]

Enter a time period before switching to the sleep mode when this machine
is not being operated.

[Power Save Key]

Configure the type of the power save function to be started when you press
the

Power Save

key.

[Low Power]

Provides power-saving effect higher than normal.

[Sleep]

Provides power-saving effect higher than the low
power mode. However, the machine must be
warm-up when restarting operations, therefore
taking more preparation time than the low power
mode.

[Enter Power Save Mode]

Configure settings for switching to the power save mode after printing doc-
uments from computers or receiving faxes.

[Normal]

Enters the power save mode when the time spec-
ified in Low Power Mode Settings has elapsed.

[Immediately]

Enters the power save mode in a short time.

Factory default

[Low Power Mode Set-
tings]

15 min.

[Sleep Mode Settings]

20 min.

[Power Save Key]

[Low Power]

[Enter Power Save Mode]

[Immediately]

«
...
150
151
152
153
154
...
»

Summary of Contents for d-Color MF220




























































































































































































































































































































Reviews:

No comments

Related manuals for d-Color MF220

Brand: QMS Pages: 2

Brand: Oki Pages: 4

Brand: Oki Pages: 40

Brand: Oki Pages: 507

Brand: Oki Pages: 176

Brand: Samsung Pages: 351

SCX 4500W - Personal Wireless Laser Multi-Function...

Brand: Samsung Pages: 113

imageRUNNER ADVANCE 8105

Brand: Canon Pages: 5

imageCLASS MF269dw

Brand: Canon Pages: 32

Brand: Samsung Pages: 158

Brand: Tektronix Pages: 286

Brand: Evolis Pages: 45

WorkCentre PE120i

Brand: Xerox Pages: 8

Brand: EFI Pages: 4

Brand: Copystar Pages: 2

Executive Series 3037

Brand: Oki Pages: 546

apeosport 550 I

Brand: Xerox Pages: 160

Brand: ZKTeco Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands