Oliver LEGACY ELITE 2022, Manual

Page: 336 / 410

336
!
!
2
!
!
1.
2.
1.
3.
1.
3.
2.
3.
1.
2.
4.
5.
4.
2.
3.
4.
6.
warnings
Do not place the unit in water greater than one inch deep,
or water may damage the electronics.
Do not install or operate the antenna in winds of 35 mph
or greater. The antenna will roll in winds ≥35 mph.
Care should be taken when transporting and setting up the
antenna. Do not toss or drop the antenna.
Do not paint the antenna. Painting the antenna may cause
signal degradation and will void your warranty.
switch settings
the Carryout G2
+
antenna switch settings are located on
the winegard Power Inserter and are preset for DIreCtV
programming.
to set the antenna for any other programming provider,
locate the switches on the Power Inserter and set according
to the diagram below:
switch settings—Up ( ) or Down ( )
the Carryout G2
+
is preset
for DIreCtV programming.
the switch settings must be
changed to receive DIsH or
Bell tV programming.
Installing the Handle
Locate the two screws for the handle in the base. remove
the screws from the base with a Phillips screwdriver.
NOTE
the two holes for the handle are located between
the cable connections and eyelet.
Locate the handle in the box. with “wIneGArD” on the
handle facing upwards, align the two holes in the handle
with the two holes in the base.
thread two screws through the two aligned holes in the
bottom of the handle.
tighten the two screws using a Phillips screwdriver.
Do not overtighten.
Choosing a Location
Choose a location with a clear, unobstructed view of the
southern sky. Avoid obstructions such as trees, hills, vehicles,
or buildings—these can block the signal from the satellite.
NOTE
satellite signal will not pass through solid objects. For
this reason, it is vital to select a location with a clear,
unobstructed view of the southern sky.
Make sure the antenna is not placed in the path of people or
vehicles; otherwise, the antenna may be knocked off of the
signal if run into, or cables may be disconnected from the unit.
select a location that will enable the Carryout G2
+
antenna to
sit within three degrees of level. the antenna may take longer
to lock onto signal if the antenna is not level.
wiring the Antenna
TIP
run the coaxial cable directly from the satellite receiver
to the Carryout G2
+
antenna when searching for signal.
ensure the power button on the winegard Power
Inserter is in the oFF position (not pressed in).
Connect the included 25’ coaxial
cable between the primary port
of the Carryout G2
+ and the
AntennA port on the Power
Inserter. tighten coax connections
until finger tight, and tighten a
quarter turn more with a wrench.
Do not overtighten.
NOTE
A 25’ coaxial cable is
included with the antenna.
to ensure proper operation, use only
the included coaxial cable. Failure to
use the included coax cable or use of
the interior/exterior pre-wiring could
hinder proper operation.
Connect the included 3’ coaxial
cable between the “sAt In” port
of your satellite receiver and the
reCeIVer port of the winegard
Power Inserter. tighten coax
connections until finger tight, and
tighten a quarter turn more with a
wrench. Do not overtighten.
Plug power adapter into
110/120VAC outlet and connect
to power port on Power Inserter
(located next to reCeIVer coax
port).
once system is fully connected,
press the power button on the Power Inserter.
Give the Carryout G2
+
antenna approximately 3-5 minutes
to complete the search sequence. once the Carryout G2
+
antenna has gone completely quiet, proceed to configure
receiver for desired operation. For DIreCtV, see page 3.
For DIsH, see page 4.
Power Inserter switches
Power
Inserter
Receiver
Coax to
Antenna
Carryout G2
+
Antenna
1 2 3 4 5 6 7 8
DIRECTV
1 2 3 4 5 6 7 8
DISH Bell TV
1 2 3 4 5 6 7 8
WINEGARD CARRYOUT G2+ SATELLITE ANTENNA