OKIDATA ML320 Turbo Service Manual Download

Page: 74 / 294

Page: 43

Service Guide ML320/ML321

Chapter 3 Maintenance & Disassembly

3.2.03 Printhead Assembly

WARNING:

The printhead will be hot immediately after printing.
Allow the printhead to cool before handling.

Perform these procedures first:

- 3.2.01 (

)

- Open the access cover (1).

- Remove the ribbon cartridge (2).

- Move the printhead mounting clamp (3) in the direction of arrow A to unlock
the printhead (4).

- Lift and remove the printhead from the carriage frame (5).

NOTE: When installing the printhead, push the printhead towards the platen.

Summary of Contents for ML320 Turbo















































































































































































































































































Search results

Summary of Contents for ML320 Turbo

Reviews:

Related manuals for ML320 Turbo

Brands by name

Popular brands

OKIDATA ML320 Turbo, Service Manual

Search results

Summary of Contents for ML320 Turbo

Reviews:

Related manuals for ML320 Turbo

Brands by name

Popular brands