manualshive.com logo in svg

Oki IP-5530, User Manual, Page: 98 / 265

Share
Download
Oki IP-5530 User Manual Download Page 98

98

Maintenance

Completely clogged nozzle

Will be substituted.

105

106

107

Normal nozzle

Will not be substituted.

105

106

107

Partially clogged nozzle

Will be substituted or not depending on its condition.

105

106

107

g

 Go to STEP 2

105

106

107

g

 Go to STEP 2

Nozzle that does not eject ink straight

Will not be substituted.

105

106

107

g

 Go to STEP 2

           <STEP 2>

If there are defective nozzles that have not been set, add them manually as shown in manual configuration on 

 

page 94

.

In case there are nozzles that are always defective, you can set overwrite protection when selecting the nozzles 
to always substitute them with other nozzles regardless of the detection results of automatic configuration.

Overwrite protection setting

VAR: Not overwrite protected
FIX: Overwrite protected

 

 

š

The numbers of defective nozzles are easier to find while looking at the print result of automatic nozzle map 
when setting the nozzles.

1

 

 

PRINTER READY 
01: PAPER / 1626mm

 

                 

  

Press the 

ADJUST

 button. 

You can set up to 10 nozzle map parameters for each print 
head.

2

 

 

ADJUST  

   

2

MEDIA ADVANCE 

 

                 

  

, 

Press the 

Up

 and 

Down

 buttons to select 

SET 

NOZZLE MAP

. 

Summary of Contents for IP-5530










































































































































































































































































Reviews:

No comments