manualshive.com logo in svg

Oki IP-5530, User Manual, Page: 126 / 265

Share
Download
Oki IP-5530 User Manual Download Page 126

126

Maintenance

J Printer cleaning 

Clean the printer when the dirt becomes noticeable. Clean the printer approximately once per week.
 

Media edge guards

Platen

Paper guide

Pressure roller

Front cover

 

 

Head guard cleaning 

1

 

PRINTER READY 
01: PAPER / 1626mm

 

                 

  

Press the 

MAINTENANCE

 button.

2

 

MAINTENANCE  

   

2

START MAINTENANCE 

 

                 

  

Press the 

Down

 button to select 

PH 

MAINTENANCE

.

3

 

MAINTENANCE  

   

2

PH MAINTENANCE 

 

                 

  

Press the 

OK

 button.

4

 

>PH MAINTENANCE  

   

2

SET PH FOR CHECK 

 

                 

  

, 

Press the 

Down

 button to select 

SET PH FOR 

CHECK

, and then press the 

OK

 button.

Maintenance when the printer 

is dirty

Summary of Contents for IP-5530










































































































































































































































































Reviews:

No comments