Home
/
Oki
/
IP-5530
/
User Manual

Oki IP-5530, User Manual, Page: 231 / 265

Share

Page: 231 / 265

Oki IP-5530 User Manual Download Page 231

231

Troubleshooting

Media wrinkles have been detected

Using the safe scanning system, the Printer detects the media wrinkles during printing. When media wrinkles have
been detected, the Printer enters the pause mode and a message appears on the operation panel so that you can
select to continue or stop the print.

The Printer enters the pause mode when…

The Printer enters the pause mode when safe scanning is set to SUSPEND PRINTING or
SUSPEND&WARNING.

PRINTING...
STANDARD ND BI

(When media wrinkles have been detected)

REMOVE MEDIA WRINKLE
PRINT? OK/CANCEL

When media wrinkles have been detected
- The ONLINE LED flashes slowly.

REMOVE MEDIA WRINKLE

PRINT? OK /C ANCEL

(When printing continues)

(When printing is canceled)

Stop printing with the Cancel button.

When the Printer is in pause mode, the front cover can be
opened and closed and the pressure roller up/down lever
can be operated without canceling the job being printed.
When you want to continue the printing, first remove the
media wrinkles before resuming the print.

LIFT THE LEVER AND
LOAD THE MEDIA

When you continue the printing…

If you select CONTINUE to continue the print, the printing of the rest of the suspended job is resumed. However, it
may happen that the media wrinkles become bigger and that a media jam occurs.
When the printout is lengthy, the media wrinkles may also become bigger, which may damage the Printer.
Therefore, it is recommended to stop printing.

«
...
229
230
231
232
233
...
»

Summary of Contents for IP-5530










































































































































































































































































Reviews:

No comments