Oki IP-5530 User Manual Download Page 229

Page: 229 / 265

229

Troubleshooting

OPEN COVERS

Open the front cover, and then the capping
unit cover.

INSERT SHEET MOUNT
CLNG LQD INTO CAPS

Use the dropper to fill the cap of each color
with sheet mount cleaning liquid.

CLOSE COVERS

Close the capping unit cover and the front
cover.

CARRIAGE IS MOVING
PLEASE WAIT

Carriage stops moving.

The carriage moves to the home position.

Note

If the current procedure is interrupted by an error before the step 8, start sheet mount cleaning again from step 1.

PRESS OK TO END OPER
TIME ELAPSED

XX:XX

(Wait with the printer as it is.)

Note

The SET CAP FOR CLNG operation takes between 12 and
18 hours. After this time has elapsed, follow the panel
message and quickly end the operation.

To end the

SET CAP FOR CLNG

operation,

press the OK button.

END OPERATION AND
DRAIN CLNG LIQUID?

Press the

button.

CLNG LIQUID DRAINING
PLEASE WAIT

(Draining of the sheet mount cleaning

liquid is complete.)

Summary of Contents for IP-5530










































































































































































































































































Search results

Summary of Contents for IP-5530

Reviews:

Oki IP-5530, User Manual, Page: 229 / 265

Search results

Summary of Contents for IP-5530

Reviews: