Oki IP-5530 User Manual Download Page 178

Page: 178 / 265

178

Advanced operations

>CHANGE PRESET

02:Glossy

Press the

CANCEL

button to exit the CHANGE

PRESET menu.

>MENU

CHANGE PRESET

Press the

ONLINE

button.

PRINTER READY
02:Glossy/1626mm

Feed or rewind media

Feeding and rewinding operations can be executed in the online state (idle mode).

PRINTER READY
01: PAPER / 1626mm

Press and hold the

Down

button.

Press and hold the

Down

button.

To feed media, press the

Down

button.

To rewind media, press the

button.

When the

Down

button is pressed.

FEEDING MEDIA...

When the

button is pressed.

BACKFEEDING MEDIA…

Release the

Down

button.

Release the

Down

button.

The printer stops feeding or rewinding media, and the
display returns to online state.

PRINTER READY
01: PAPER / 1626mm

Summary of Contents for IP-5530










































































































































































































































































Search results

Summary of Contents for IP-5530

Reviews:

Oki IP-5530, User Manual, Page: 178 / 265

Search results

Summary of Contents for IP-5530

Reviews: