manualshive.com logo in svg

Oki IP-5530, User Manual, Page: 94 / 265

Share
Download
Oki IP-5530 User Manual Download Page 94

94

Maintenance

Cautions regarding automatic configuration

 Notes 

 

‹

Automatic configuration sets nozzle map mechanically, so absolute precision of the setting cannot be guaranteed.

 

‹

The printer cannot configure correctly nozzle map in the following cases. In such cases, improve the conditions or perform 
manual configuration.

- The media used makes the check via sensors impossible.
   (Some media types, even conventional ones, may not be supported by automatic configuration.)
  <Examples> 
  - Transparent media
  - Media with a rough surface
  - Media with an extremely high or low degree of reflection
  - Media on which the pattern cannot be printed properly, such as when the ink tends to bleed
  - Media where density differences do not appear on the printed pattern.
  - Media that does not advance smoothly
  - Media that wrinkles easily
- The media surface is soiled with dust, ink, finger marks, etc.
- A gap tends to form between the platen and the media
- Lots of nozzles are clogged
- The media heater temperatures are not suitable
- The environmental luminosity is too strong
- The bidirectional or media advance adjustment value is not set correctly

 

‹

With automatic configuration, the printed pattern is read automatically. However, discrepancies may appears in the printed 
pattern between media lots or if the media is old. Therefore, the detection results may be incorrect even when using the 
same media.

  In such cases, use manual print adjustment.

 

‹

Depending on the environment temperature and humidity, nozzles may clog after automatic configuration, even if it 
happens rarely.

  In such a case, first perform cleaning to recover the nozzles, and then perform manual configuration.

Manual configuration

1

 

 

PRINTER READY 
01: PAPER / 1626mm

 

                 

  

Press the 

ADJUST

 button. 

You can set up to 10 nozzle map parameters for each print 
head.

2

 

 

ADJUST  

   

2

MEDIA ADVANCE 

 

                 

  

, 

Press the 

Up

 and 

Down

 buttons to select 

SET 

NOZZLE MAP

. 

3

 

 

ADJUST  

   

2

SET NOZZLE MAP 

 

                 

  

Press the 

OK

 button.

4

 

 

>SET NOZZLE MAP

2

Lc 

 

            

  

, 

, 

Press the 

Up

 and 

Down

 buttons to select the 

color to be set and press the 

OK

 button. 

This example explains how to set a nozzle number 165 for 
the nozzle map 1 of Lc head.

Summary of Contents for IP-5530










































































































































































































































































Reviews:

No comments