manualshive.com logo in svg

Oerlikon CENTER TWO, Operating Manual

Share
Download
Oerlikon CENTER TWO Operating Manual Download Page 99

98

GA 09.035/6.02 - 07/2011 - © Oerlikon Leybold Vacuum

Appendix

Degas function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31
Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26
Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31

, 

71

Switching on

Degas function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30
Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26
Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30

, 

71

Switching the emission on  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  45

T

Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9
Test parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  52

A/D converter ID  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55

, 

79

A/D converter signal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55

, 

79

Display test  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55

, 

79

EEPROM test  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54

, 

80

EPROM test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54

, 

80

Firmware version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  52

, 

73

I/O test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55

, 

81

Keyboard test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  82
Parameter setup lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53

, 

72

RAM test  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54

, 

83

RS232C test  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  56

, 

83

Selection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  52
Torr lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53

, 

83

Watchdog control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53

, 

84

Threshold values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36

, 

77

Adjustment range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38

Torr lock  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53

, 

83

Transmitter

Degassing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30
Identifying  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32
Selecting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  29
Switching off  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31

, 

71

Switching on  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30

, 

71

Transmitter control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  44

, 

77

Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  90
Type label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4

U

Unit of measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  47

, 

84

Update  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  85
Upper threshold value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36

Adjustment range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38

W

Waiting time  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5
Watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  53

, 

84

Summary of Contents for CENTER TWO







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands