Oerlikon Leybold Vacuum Turbovac SL 300 Operating Instructions Manual Download Page 58

Page: 58 / 64

Troubleshooting

130000761_002_A0 - 08/2008 - © Oerlikon Leybold Vacuum

Error
code

Error

Possible Cause

Remedy

Shut-
down

–

Yellow power LED is not
on

No DC power
DC power miswired
Frequency converter defective

Check cables and power supply
Ensure correct polarity of the DC cable.
Replace frequency converter. The following

may damage the freq. converter:

■

Disconnection of the DC

cable while the pump was still rotating

■

Non-compliance with the note related to

connecting several pump to a single power

supply.

–

div.

Red LED flashes

Warning message.

See Section “3.3.6 Warning

codes” for the possible reasons of

the warning.

The pump can continue to

run, as long as operation limits are only

exceeded for a short time. In case of longer

exceeding send pump and frequency conver-

ter to the OLV service.

–

Turbomolecular pump

does not start, ERROR

LED does not light.

Interface protocol error
No communication via the serial

interface.
REMOTE connector (X1) connec-

ted wrongly.
REMOTE and SERVICE connec-

tors mixed up.
Wrong Profibus address set.

Use USS protocol.
Connect bus as shown in Section 3.3.

Connect as shown in Fig. 2.19

Connect correctly.

Set address between 0 and 126.

–

Turbomolecular pump

produces loud running

noises and vibrations.

Rotor out of balance
Bearing defective

Balance the rotor
Replace the bearing

–

Turbomolecular pump

does not reach ultimate

pressure.

Measurement instrument defective
Measurement sensors soiled
Leaks at the equipment, lines or

the pump
Pump soiled
Forevacuum pump provides insuffi-

cient pumping speed or ultimate

pressure which is too high.
Frequency parameters program-

med wrongly

Inspect the measurement sensor
Clean or replace the sensors
Check for leaks

Clean the pump
Check the ultimate pressure of the forevacu-

um pump and install a higher-capacity vacu-

um pump if necessary
Check parameters.

–

Running pump can not

be stopped via X1

Pump has been started via the

serial interface, the interface con-

trols the pump

Disconnect the DC supply or connect serial

interface and stop via bus

Summary of Contents for Turbovac SL 300

































































Search results

Summary of Contents for Turbovac SL 300

Reviews:

Related manuals for Turbovac SL 300

Brands by name

Popular brands

Oerlikon Leybold Vacuum Turbovac SL 300, Operating Instructions Manual

Search results

Summary of Contents for Turbovac SL 300

Reviews:

Related manuals for Turbovac SL 300

Brands by name

Popular brands