manualshive.com logo in svg

Oce TDS860, User Manual

Share
Download
Oce TDS860 User Manual Download Page 93

Using the Océ TDS600 scanner to copy

93

Deliver originals after scanning

You can choose for delivery of the original at the front (rewind) or the rear side 
of the scanner.

Attention: 

The ‘Rewind’ function is disabled when the optional original 

delivery tray is installed.

Note: 

When you copy thick or very thin originals, originals that are damaged 

or originals in a carrier sheet, it is recommended to use the output at the rear 
side of the scanner to ensure correct delivery (‘Rewind’ function off).

▼

Select original delivery

1

Open the ‘Scanner’ card in the ‘Original’ section.

2

Press the ‘Rewind original’ function key to make your selection:

■

‘On’: Originals are delivered at the front side of the scanner. You have to 
collect each original by hand.

■

‘Off’: Originals are delivered at the rear side of the scanner.

[42] Using the Rewind original function to select original delivery at the front or the rear

Access to

ial

Access to

Page

Interrupt

job

Summary of Contents for TDS860











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands