manualshive.com logo in svg

Oce TDS860, User Manual

Share
Download
Oce TDS860 User Manual Download Page 117

Using the Océ TDS860 to scan-to-file

117

Zoom

The ‘Zoom’ option allows you to scale while scanning to a file. When you set 
‘File mode’ to ‘On’ then the automatic ‘Zoom’ setting will result in ‘1:1’. You 
can change this default setting to one of the following three settings:

Custom  

This option lets you specify a custom zoom value. You can enter a 

range from 25% through 400%. This value also shows the zoom value when 
the option ‘Automatic’ is chosen.

1:1  

With this option selected, scan-to-file will result in an image that is exactly 

the same size as the original. ‘Zoom’ displays 100%.

Automatic  

Selecting ‘Automatic’ always results in a 1:1 scan-to-file. 

Optimization

There are two ways to optimize a scan-to-file

Scan quality  

optimizes for the best image quality. The scan resembles the 

original as close as possible.

File size  

optimizes for better compression. Generally resulting in a smaller file 

size. Image quality can slightly decrease.

Mirror

You can use the ‘Mirror’ option to scan a horizontally mirrored image of an 
original. Mirroring is performed in the vertical axis.

Summary of Contents for TDS860











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands