manualshive.com logo in svg

Oce TDS860, User Manual

Share
Download
Oce TDS860 User Manual Download Page 277

Problem solving

277

Caution: 

Do not hold your hand between the green lever and the lower 

cover when you close the cover. The lever moves toward the cover and can 
cause personal injury.

19

Unlock the green bar and close the top cover. 

If you can not correct the problem, you can open the output transport unit and 
remove the paper (see Figure 180 on page 277). If the fuser-section covers 
remain to flash on the display, check the fuser section again.

[180] Open the transport output unit

Paper jam in the paper roll compartments

▼

How to clear a paper jam in the paper roll compartments

Note: 

Make sure that you corrected all the problems in the fuser section, 

before you correct the problem in the roll feed section.

1

Completely open the correct paper roll compartment. 

2

Remove any jammed paper:

■

Behind the chip tray

■

Underneath the plate

■

Underneath the roll 2, the roll 4 or the roll 6 feed plate

3

Reload the roll if necessary.

4

Close the paper roll compartment.

Summary of Contents for TDS860











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands