manualshive.com logo in svg

Oce TDS860, User Manual

Share
Download
Oce TDS860 User Manual Download Page 37

Using the Océ TDS860 to print

37

The following keys are available: 

Key types

Key

Function

Selection
keys

The selection keys are located immediately below the graphical 
display. The left key can be used to activate one of the main menu 
choices (Language, Folding or 

 

Media) on the left part of the display. 
Note: A shadow highlighting effect is used to indicate the active 
menu option.
The right selection key can be used to activate the options on the 
right part of the graphical display.
Note: To identify the active selection, the dotted line around this 
selection is changed into an uninterrupted line and the small 
selection triangles next to the specified option are no longer 
dimmed.
These selection triangles indicate that you can select an option 
from a predefined list with the help of the arrow keys.

Arrow 

 

keys 

These two triangular keys to the right of the graphical display are 
used to display the next or previous option from the selected menu 
choice and to select the desired option.

On-line key

By pressing the On-line key you can put the printer On-line or 
Off-line. If the green light above the On-line key is on, the printer 
is On-line; if this light is off, the printer is Off-line.

Stop key

The red Stop key is used to stop the present print job. After this 
key is pressed, a dialog is displayed asking for confirmation.

Note: The printing process does not stop instantaneously since a 
number of prints may already have been submitted to the printer 
after processing. The prints cannot be stopped.

Extra key

This key is reserved for future use.

Summary of Contents for TDS860











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands