Oce TDS860 User Manual Download | Manualshive

Page: 116 / 330

background image

116

Océ TDS860 User Manual

Note:

Only choose ‘Group 4’ or ‘Group 3(-1D)’ when you are sure you can use

these compressions afterwards. Choose ‘None’ in any other case.

Note:

If you scan grayscales or dark originals, then use Group 3(-1D)

compression. In these cases group 4 can increase the file size.

Note:

‘Group 4’ or ‘Group 3(-1D)’ are compression methods which are

optimized for text and vector drawings. If you choose these compressions when
scanning a photo with many grayscales, these compressions can result in a
negative compression: the file size increases instead of decreases. So use these
compressions with care.

PDF compress

Within the ‘PDF compress’ option, you can define the ‘Compression’ of the
file.

Compression

can be (select with the arrow keys):

■

Group 4

■

None

Note:

Only choose ‘Group 4’ when you are sure you can use this compression

afterwards. Choose ‘None’ in any other case.

Resolution

The scan-to-file option allows you to scan at the following three resolutions:

■

200 dots per inch (dpi)

■

300 dpi

■

400 dpi

The higher the resolution the better the image quality. Higher resolution also
leads to larger file sizes. The default value is 200 dpi.

«
...
114
115
116
117
118
...
»

Summary of Contents for TDS860











































































































































































































































































































































Reviews:

No comments

Related manuals for TDS860

All in One Printer

Brand: Xerox Pages: 3

MultiPASS L6000

Brand: Canon Pages: 251

MultiPASS C5500

Brand: Canon Pages: 24

MultiPASS L6000

Brand: Canon Pages: 24

Laser Class 700 Series

Brand: Canon Pages: 221

Brand: Canon Pages: 18

Brand: Canon Pages: 16

Brand: Canon Pages: 39

Brand: Canon Pages: 2

Brand: Canon Pages: 73

Brand: Canon Pages: 29

Brand: Canon Pages: 16

Brand: Canon Pages: 44

Brand: Canon Pages: 60

Brand: Olympus Pages: 236

I450 - i 450 Color Inkjet Printer

Brand: Canon Pages: 13

Brand: Panasonic Pages: 54

Brand: Panasonic Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands