Oce TDS860 User Manual Download

Page: 245 / 330

Media and supplies

245

Hit the bottom of the bottle.

Note:

Just add one bottle at a time.

When the bottle is empty, remove the bottle.

Close the fill opening

Lift top cover and pull the hinge towards you to close the top cover (see
figure 139).

[139] Close the top cover

Fasten the cap on the empty toner bottle. The Océ service engineer takes the
empty toner bottles with him at the next visit.

Attention:

If you have spilled some toner, (see ‘Safety data sheet Océ

TDS600 scanner’ on page 315) for information about disposal and
cleaning.

Summary of Contents for TDS860











































































































































































































































































































































Search results

Summary of Contents for TDS860

Reviews:

Related manuals for TDS860

Brands by name

Popular brands

Oce TDS860, User Manual

Search results

Summary of Contents for TDS860

Reviews:

Related manuals for TDS860

Brands by name

Popular brands