manualshive.com logo in svg

Oce TDS860, User Manual

Share
Download
Oce TDS860 User Manual Download Page 24

24

Océ TDS860 User Manual

▼

Turn the Océ TDS860 printer on and off

1

Turn the key to the ‘on’ position (see figure 2).

 

The system takes about 20 minutes to warm up. When the system is warmed 
up, the message ‘Ready to...’ appears on the printer operator panel.

2

Turn the key to the ‘off’ position (see figure 2).

Note: 

Before you turn the printer off, make sure that the printer is not 

printing a job.

[3] Power switch with key in the timer position on the Océ TDS800 scanner

▼

Turn the Océ TDS800 scanner on and off

1

Turn the key to the ‘on’ position (see figure 3)

 

After a few seconds the message ‘Ready to print’ appears on the scanner 
operator panel.

2

Turn the key to the ‘off’ position (see figure 3).

[4] On / off switch on the Océ TDS600 scanner

on

timer

off

Summary of Contents for TDS860











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands