Oce TDS860 User Manual Download

Page: 42 / 330

Océ TDS860 User Manual

Print with Océ Print Exec

Workgroup

Introduction

Océ Print Exec

Workgroup is an optional print job submission application

which allows you to send print jobs to the Océ TDS860 through your web
browser. Enable Océ Print Exec

Workgroup with a password in the Océ

Settings Editor. Océ Print Exec

Workgroup allows you to do the following.

Select and collect the files to print (documents and drawings), in a print job.

Configure the print job.

Preview the files to print.

Submit the print job.

Check the print job and the printer configuration status.

Options

Océ Print Exec

Workgroup has the following options.

■

View status information about the printer configuration and available media.

■

View status information of submitted print jobs in the historic queue.

■

Set the document or drawing settings.

■

Set the job settings for a print job.

■

Add a settings configuration for a print job.

■

Add a maximum of 100 documents or drawings to a print job.

■

Add documents or drawings from the Océ Doc Exec

archive.

■

Add a stamp to the document or drawing.

■

Add a banner to the print job.

■

Preview the document or drawing before you print.

■

Save and retrieve print jobs.

■

Submit print jobs to printer queue or inbox queue.

■

Manage serveral print jobs.

Summary of Contents for TDS860











































































































































































































































































































































Search results

Summary of Contents for TDS860

Reviews:

Related manuals for TDS860

Brands by name

Popular brands

Oce TDS860, User Manual

Search results

Summary of Contents for TDS860

Reviews:

Related manuals for TDS860

Brands by name

Popular brands