manualshive.com logo in svg

Oce TDS860, User Manual

Share
Download
Oce TDS860 User Manual Download Page 276

276

Océ TDS860 User Manual

[178] The crank

8

If the paper keeps coming, it is not cut and you have to cut it manually. 

9

Cut the paper and turn the crank to the right to deliver the paper.

10

Remove the crank and return it to its original position.

11

Pull the handle 1 towards you to open the pre-heater section (see Figure 179 on 
page 276).

12

Pull the green handle 2 toward you and release handle 1 (see Figure 179 on 
page 276).

13

Pull the green bar 3 toward you (see figure 179).

[179] The pre-heater section

Close as follows:

14

Push the bar 3 back.

15

Press the handle 1 downwards.

16

Press the handle 2 back.

17

Close the bar of the fuser section.

18

Close the lower cover of the output unit.

1

2

3

1

2

3

Summary of Contents for TDS860











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands