Oce TDS860 User Manual Download Page 230

Page: 230 / 330

230

Océ TDS860 User Manual

Maximum folding length

There are maximum values for different kind of

paper. The tables below show the maximum values for three different weights
of paper and the possible folded output for 110 grams paper.

Maximum output lengths for folding

First fold output

Stacker 2nd fold

Belt 2nd fold

Paper weight
[g/m

]

1st fold
[mm / inch]

2 folds

[mm / inch]

3 folds
[mm / inch]

2folds
[mm / inch]

1220 / 48

6000 / 236

2500 / 98

2000 / 79

1220 / 48

110

2500 / 98

1220 / 48

not possible

1220 / 48

Folding settings 75 grams

Output selection

Output length

Delivery

‘Stacker’ or ‘Belt’

< 2.5 m

Delivered on stacker or belt

‘Stacker’ or ‘Belt’

2.5 m - 6 m

First fold only, delivered in

first fold delivery

‘Stacker’ or ‘Belt’

> 6 m

length known at start

Unfolded, delivered in IRT

‘Stacker’ or ‘Belt’

> 6 m

length not known at start

Possible paper jam

‘Stacker’ or ‘Belt’

‘First fold only’ selected

< 6 m

Delivered in first fold delivery

‘First fold only’

> 6 m

length known at start

Unfolded, delivered in IRT

‘First fold only’

> 6 m

length not known at start

Possible paper jam

Summary of Contents for TDS860











































































































































































































































































































































Search results

Summary of Contents for TDS860

Reviews:

Brands by name

Popular brands

Oce TDS860, User Manual

Search results

Summary of Contents for TDS860

Reviews:

Brands by name

Popular brands