manualshive.com logo in svg

Oce TDS860, User Manual

Share
Download
Oce TDS860 User Manual Download Page 9

Contents

9

Chapter 14

 

Maintenance

Maintenance of the reference roller of the Océ TDS800 scanner   248
Maintenance of the glass platen and the reference roller of the Océ TDS600 
scanner   250
Maintenance of the Reinforcement Unit   252

A new tape roll   252
Clear the waste box   260
Clean the reinforcement knives   261

Maintenance of the punch unit   263

Chapter 15

 

Problem solving

Introduction   266
How to clear original jams (TDS800-scanner)   267
How to clear original jams (TDS600-scanner)   269
How to clear paper jams   271

Paper jam in the manual feed   272
Paper jam in the fuser section   273
Paper jam in the paper roll compartments   277
Paper jam behind the chip tray   278
Paper jam in the vertical transport unit   279
Paper jam underneath the roll 1, roll 3 and roll 5 triangular feed unit   280
Paper jam in the first fold section of the folder   281
Clear a paper jam in the high capacity output unit of the folder   285

Problems with the Reinforcement Unit   288

Clear paper jams in the Reinforcement Unit   288
Clear tape jams in the Reinforcement Unit   290
No reinforcement strips on the output without an error message   292

Other problems   294

Appendix A

 

System specifications

Product specifications Océ TDS860   296
List of available material types and sizes   306

Reinforcement strips   307

Summary of Contents for TDS860











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands