NTT docomo FOMA N706i, Instruction Manual

Page: 401 / 519

399 Continued on next page
Appendix/Exte
rnal De
vic
es/T
roub
leshooti
ng
If Any Error Message Appears
z
In the following table, error messages are written in
color, and explanation/solution and reference
pages are written in black.
z
Error messages are described in alphabetical and
Kana order.
z
Numbers in parentheses are codes used by the
i-mode Center as separators between transmitted
errors.
“ACMmax restriction cannot call”
• This is displayed when a call cannot be made because
you have exceeded the accumulated charge upper limit
that is pre-set in your FOMA card. To release the
restriction, perform “Reset total cost”.
→ P.322
“Activating restrict dialing”
●
This is displayed if you attempt a prohibited operation
while Restrict dialing is set.
→ P.123
“Activating Box lock Cannot download”
●
There is a lock on the inbox and outbox as a whole, or
on folders using mail-linked i-
α
ppli, so mail-linked
i-
α
ppli cannot be downloaded or upgraded. To
download or upgrade the mail-linked i-
α
ppli, release
the Mail box lock. → P.122
“Activating Box lock Unable to delete”
●
There is a lock on the inbox and outbox as a whole, or
on folders using mail-linked i-
α
ppli, so the mail-linked
i-
α
ppli and the folders using them cannot be deleted.
To delete the mail-linked i-
α
ppli and the folders using
them, release the Mail box lock.
If you delete only the mail-linked i-
α
ppli, a message will
be displayed asking whether to delete the
corresponding mail folders dedicated to that i-
α
ppli.
Select “NO”.
→
P.122
“Activating Folder lock Cannot download”
●
See “Activating Box lock Cannot download” (P.399) for
the explanation and solution.
“Activating Folder lock Unable to delete”
●
See “Activating Box lock Unable to delete” (P.399) for
the explanation and solution.
“Address is not valid (451)”
●
Displayed when the mail has not been sent to the
specified address correctly.
→ P.172
“Attached file is deleted”
●
This message appears when an i-mode message
received that you attempt to quote to send a reply has
any file attached. It is also displayed if you attempt to
forward an i-mode mail that has a file attached that is
prohibited from being attached to mail or output from
the FOMA terminal. The attached file is deleted when
you press
d
.
“Authentication cancelled (401)”
●
This is displayed when the Cancel button is pressed on
the Authentication screen.
“Authentication type not supported (401)”
●
This is displayed when authentication fails. Press
d
to
return to the original page.
“Cannot activate 1Seg Release Self-mode or
move to FOMA area”
●
1Seg is viewed repeatedly in communication-
impossible situations such as in Self-mode and out of
range, and cannot activate. Release Self-mode or
move to the FOMA range then re-activate 1Seg.
“Cannot dial by Number B in abroad. Dial by
Number A”
●
This is displayed when the 2in1 mode is set to B mode
and you attempted to make a call while overseas.
Select OFF for “Caller ID Notification” to make calls
without caller ID with Number A.
“Cannot download because the IC card is full.
Delete a service?”
“Cannot upgrade version because the IC card is
full. Delete a service?”
“Cannot start because the IC card is full. Delete a
service?”
“Cannot move because the IC card is full Delete a
service?”
●
This is displayed when an Osaifu Keitai-related i-
α
ppli
is downloaded or moved from a microSD card but there
is not enough data capacity left on the IC card. Select
“YES” to display a list of the Osaifu Keitai service
names already registered, the space (bytes) which
would be freed by deleting each service, and the size of
the capacity shortage. Select one or more services to
delete, then follow the messages to start an i-
α
ppli to
delete them.
“Cannot download because UIM information does
not match”
“Cannot move because UIM information does not
match”
“Cannot save because UIM information does not
match”
“Cannot start because UIM information does not
match”
“Cannot delete because UIM information does not
match”
“Cannot backup because UIM information does
not match”
●
This is displayed when the inserted UIM does not
match the UIM information registered for FeliCa and
moving i-
α
ppli from a microSD card.