NTT docomo FOMA N706i, Instruction Manual

Page: 354 / 519

352
Netw
ork Ser
vices
⑤ Answer message (Record message)
setting: Go to the operation after
selecting “ON” in Step 1 in the “Record
message” (P.68)
2in1 function OFF …… Sets 2in1 to OFF.
Rcv. avoid. setting …… Restricts incoming calls for
Number A and Number B.
Change rcv. avoid. …… Sets the Rcv. avoid.
setting for Number A and Number B.
Check rcv. avoid. …… Checks the Rcv. avoid.
setting for Number A and Number B.
Mode link …… Sets the linkage for changing
2in1 mode and Rcv. avoid. setting. Incoming
calls only for Number A are accepted in A
mode, incoming calls only for Number B are
accepted in B mode, and incoming calls for
both mode are accepted in Dual mode.
* When the function is activated, you cannot
switch the mode with “ ” displayed.
Rcv. avoid. (abroad) …… Sets the Rcv. avoid.
setting overseas (when Mode link is active, the
Rcv. avoid. (abroad) is disabled).
Switching phone numbers each time
when making a call
When 2in1 is set to ON and the mode is set to Dual
mode, phone numbers can be switched when making
a call.
z
This function is available only on the detail screen
of “Phonebook/Received calls/Dialed calls/Redial”.
<Example: When making a call using the
phonebook>
1 Phonebook detail screen (P.79)
u
(FUNC) “Dial setting” “2in1/Multi
Num.” Select any item:
Number A
……
Allows calls to be made from Number
A.
Number B …… Allows calls to be made from Number
B.
Cancel number
……
Releases the setting and allows
calls to made according to Phonebook 2in1 setting.
N
z
When 2in1 is set to OFF, you can also perform “2in1
settings” by pressing
2
for 1 second or longer on
the standby screen.
<Mode switching>
z
You can also change mode by pressing
2
for 1
second or longer on the standby screen.
<Phonebook 2in1 setting>
z
You cannot set this function to UIM phonebook
entries.
z
Select “Display detail” from the function menu to
display “Phonebook detail screen” from “Phonebook
list screen” in this function.
<Standby display>
z
When Change Mode is set to A mode, standby
screens are displayed according to “Display setting”.
z
When set to the Kisekae Tool you downloaded, the
i-
α
ppli standby screen or the random display, the
default screen appears even when “Same as Number
A” is set.
<Disp. call/receive No.>
z
Names, phone numbers and mail addresses in the
screens below will be displayed in the set color.
• In-call screen
• Dialing/Receiving screen
• Redial/Dialed calls (list/detail)
• Received calls (list/detail)
• Sent
*
/Received address record screen (list/detail)
• Chaku-moji Sent messages record screen
* : In B mode, the screen for sent addresses cannot be
displayed.
z
The setting for Number A/Number B (Address A/
Address B) is referred in the screen while incoming a
call, etc. even when 2in1 is set to OFF.
<Ringtone for Number B>
z
When making the same settings to Number A and
Address A, set each item as “Same as Number A”.
z
When the ring tone settings are duplicated, the priority
applies.
→
P.91
When you receive a call without caller ID on Number
B, priority is given to the “Ringtone for Number B”
setting.
N
z
“2in1/Multi Num.” in the function menu cannot be
selected when the mode is set to A mode or B mode.
N