NSC Sicherheitstechnik Solution F2 Operating And Installation Manual Download | Manualshive

Page: 37 / 49

background image

NSC Sicherheitstechnik GmbH

37/47

2011 / 04 / 26

Eckendorfer Str. 125 c

Installation Manual Solution F2 20110509.doc

33609 Bielefeld

Version S031A01.01

PC software "Invalid Handle"
The USB communication between Solution F2 and PC is not working.
Remedy: 1. disconnect and connect again USB cable.

2. check the Windows system settings for display of any driver conflicts

PC Software "Timeout Solution F2 Response"
The Solution F2 doesn't answer to commands from PC
Remedy:  leave flash update routine by "ESC" and retry by pressing '2'.

PC Software "Erase error"
If the FCP only displays "----" as status for any controller, erasing has been successful but probably a
timeout has occurred on PC and and success message has not been received.
Remedy:  deactivate the erase function and program again that microcontroller.

If the flash memory is marked as "not empty" also at the Solution F2, the command hasn't been executed
correctly.
Remedy:  exit flash update reoutine at FCP by pressing 'ESC', restart by pressing '2' and retry
programming from PC again.

PC Software "Update error"
During programming one or more errrs occurred. The programmed firmware must not be used, probably
the firmware file is damaged.
Remedy:  1. retry flash update with same firmware file

2. retry flash update with new firmware file

PC Software "Checksum F2 Response"
Communication error between PC und Solution F2
Remedy: retry the last executed function.

PC Software "Unexpected F2 Response : Cmd = ...."
The Solution F2 answered with unexpected data
Remedy: use latest version of PC configuration software.

«
...
35
36
37
38
39
...
»

Summary of Contents for Solution F2


















































Reviews:

No comments

Related manuals for Solution F2

Brand: Paratec Pages: 8

Brand: J+J Pages: 33

Brand: Gardner Denver Pages: 22

Brand: B&G Pages: 2

Brand: Hanna Instruments Pages: 54

Brand: Hanna Instruments Pages: 2

Brand: Maestra Pages: 22

Brand: Mackie Pages: 4

Brand: Samson Pages: 56

Brand: EasyIO Pages: 17

Brand: National Instruments Pages: 17

Brand: Davey Pages: 12

Brand: nvent Pages: 6

Brand: Smart Vision Pages: 5

Brand: Teledyne Pages: 47

Brand: Western Co Pages: 14

Brand: Cypress Pages: 3

IB-TRON 4000 SOL

Brand: INSBUD Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands