NSC Sicherheitstechnik Solution F2 Operating And Installation Manual Download Page 12 | Manualshive

Page: 12 / 49

background image

NSC Sicherheitstechnik GmbH

12/47

2011 / 04 / 26

Eckendorfer Str. 125 c

Installation Manual Solution F2 20110509.doc

33609 Bielefeld

Version S031A01.01

Also all loopsounders belong to the external
sounders.

comes in the sounders / strobes will not be
activated again until they are switched on again.

02.7

Switch on/off

1. Zones & detect. 5. Sounder/Strobe
2. Output          6. Alarm Trans.Dev.
3. Relay           7. Delay
4. Power Output    8. Fire Outputs

Cancel                  off

"Transmission devices" are all power outputs, relays
and outputs, which are configured to switching
function „on/off like transmission device“.

Switching on/off: Alarm Transmission Device
(TD)

After selecting this function in the switch on/off main
menu you see at the bottom line of the LCD "off“
(F3) or "on“ (F2).

By pressing F3 the Alarm transmission device will be
switched off continuously.

The current status of the TD will additionally
indicated by the yellow LED on the control panel.

02.8

Switch on/off

1. Zones & detect. 5. Sounder/Strobe
2. Output 6. Alarm Trans.Dev.
3. Relay 7. Delay

4. Power Output 8. Fire Outputs

Cancel on

Switching on/off: Alarm transmission delay

Here the delay of the alarm transmission device of the
FCP „Solution F2” can be switched on/off.

After selecting this function you see at the bottom line
of the LCD "off“ (F3) or "on“ (F2). “On” means to
activate the delay (Day Mode)

The current status of the delay will be additionally
indicated by the green LEDs (Delay, No Delay) on
the control panel.
When the delay is activated there is an additional
indication in the LC module (“Delay activated”)

Pay attention :
To switch on the delay of the alarm transmission
device is only possible if “Response time” and
“Inspection time” are configured. This can only be
done by the installer company.

02.9

Switch on/off

1. Zones & detect. 5. Sounder/Strobe
2. Output          6. Alarm Trans.Dev.
3. Relay           7. Delay
4. Power Output    8. Fire Outputs

Cancel off

Switching on/off: Fire protection outputs

This function disables all outputs which have been
configured to "switch on/off like fire protection
outputs".
This disablement only is possible in case of no
alarm.

After selecting this function you see at the bottom line
of the LCD "off“ (F3) or "on“ (F2).

Pay attention :
By the function (F3) all fire outputs will be switched
off continuously. If an alarm comes in no output will
be activated.

03

Alarmcounter

FCP - Alarm : 0025
Testalarm : 0011

cancel

Alarmcounter

It is a 4 digit number (1 – 9999).
Testalarms (Detector test/revision) will be displayed
by a seperate counter.

«
...
10
11
12
13
14
...
»

Summary of Contents for Solution F2


















































Reviews:

No comments

Related manuals for Solution F2

Brand: Samson Pages: 100

Brand: Radio Shack Pages: 3

Brand: Ransburg Pages: 49

Brand: Balboa Pages: 2

Brand: Badger Meter Pages: 20

Brand: Lawler Pages: 4

Brand: Barco Pages: 6

Brand: CAME Pages: 98

Brand: CAME Pages: 16

Brand: CAME Pages: 8

Brand: rada Pages: 16

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 8

Brand: Gate Motors Pages: 6

Brand: IDS Pages: 2

Brand: jablotron Pages: 2

Brand: Yamaha Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands