Nordson Encore HD iControl System Page 36 Hardware Manual Download

Page: 36 / 93

Installation

3-14

Part 1603054-02

2015 Nordson Corporation

For the Ethernet portion of the wiring, M12 D-coded 4 pole cables with

bulkhead connectors or plugs on each end are used.

NOTE:

Do not connect any device to the Ethernet network that is not

approved by Nordson Technical Support or Engineering.

iControl

Console

Main Electrical

Control Panel

Analog

Scanner

Controllers

iControl System

PLCs

Switch

VFDs

Reciprocator

or Oscillator

Motor

Positioner Motor

Reciprocator

or Oscillator

Motor

Positioner Motor

Figure 3-8

Ethernet Network/Gun Mover Control (Typical System)

Obsolete

Summary of Contents for Encore HD iControl System






























































































Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands

Nordson Encore HD iControl System, Hardware Manual

Search results

Summary of Contents for Encore HD iControl System

Reviews:

Related manuals for Encore HD iControl System

Brands by name

Popular brands